TP-Link AX1800 WiFi 6 Router V4 (Archer AX21) – Dual Band Wireless Internet Router, Gigabit Router, Easy Mesh, Works with Alexa – A Certified for Humans Device

I recently purchased this router, and I’m extremely pleased with its performance. Finding a router that provides reliable coverage throughout my entire house has been a challenge, but this one does the job perfectly. The signal reaches every corner of my home, and I haven’t experienced any drops or slowdowns since setting it up.The setup process was straightforward, and I was able to get everything up and running in no time. The connection is stable and strong, even in areas where other routers have struggled. I highly recommend this router to anyone needing a reliable and far-reaching Wi-Fi solution!

As a rule I like to replace wifi equipment every few years, so cost is important. This met the cost component, and was easy to program before doing the swap out so that all the devices seamlessly connected.A slight improvement on speed from my 1700, and uses the same power connector. You should note that it comes with highest power setting by default. That may or may not get you faster speeds.Something else .. It likes to slide your high speed devices back to the 2.4GHZ band sometimes if you have bot of them enabled. Not really good. If you don’t have legacy 2.4GHZ devices that rely on it, OR have so many wireless that you need the space ..then disable the 2.4GHZ altogether, and the 5GHZ performs a little better too.

We have been having poor performance from the WiFi router on the equipment provided by our cable internet provider for some time. It was so bad I had to resort to turning off WiFi antenna on my iPhone and use cellular because it would timeout on simplest internet tasks, even with an apparently strong signal and only about 20 feet from the wireless access point. Calling over WiFi was sometimes of poor quality. The network administration capabilities were very limited as well.The equipment probably at least 8 years old, and while we still need it to connect to the cable, its WiFi is turned off and replaced with the AX1800’s.The improvement with the AX1800 is remarkable. Coverage is great throughout our house even for higher bandwidth tasks.Setup was a little tricky because my phone kept reconnecting to the existing WiFi network as I updated settings for the new one. And it took awhile for me to figure out how to reconnect a few of the smart plugs.Just prior to this I had tried a range extender to fix the coverage and connectivity issues. But it only compounded them. These turned out to be related to the outdated WiFi capabilities of the older router, such as not supporting single SSID for both wireless bands.

Had it connected and working within just a few minutes. Our internet is supplied by Comcast/Xfinity and it linked up to the modem straight away.In terms of available settings and configuration options, I am accustomed to running a router with dd-WRT firmware so this is definitely not as flexible but I think it is going to be fine for our home network.Wireless coverage is better than my previous router and so far stability looks good with about 2 dozen clients connected, with roughly 10 being actively used simultaneously.Overall I am pleased with how well it works and the value for the dollar.

Disclaimer: Purchased during a limited time offer (10% off)Also disclaimer: TP-Link is the only brand of router I’ve had lasting more than 2 years before having issues. (Archer C7 previously)The Netgear R7000 Nighthawk is THE router, they said. Incredible range, they said.Get the hAP ax³, they said. Mikrotik gives you SO MUCH POWER AND CONTROL, they said.Both died in 2 years or less. The latter had an aneurism when my network enabled IPv6 despite the latest firmware. Amazing for a brand touted as stable enough to run home servers.At last: TP-Link stability I used to expect from the legendary WRT Linksys line, full 2.5Gbps ethernet, and latest wifi support. Setup is a breeze, or a button click away in my case if you do use IPv6. Reliable support. Immediately noticed an uptick in network bandwidth and responsiveness. As my residential network updates to 2Gbps, I’m finding the price point, quality, and consistency that’s making me as fond of the Archer BE550 as my C7 did.One thing of note: my speedtest results DID drop. However my page load times decreased significantly. There’s a lot to modern networking, and TP-Link considers all of it under the hood. Take that for what you will, but if you absolutely want control over that, you’re free to tinker with more “extensible” platforms like Mikrotik, but based on my experiences, good luck!

I recently upgraded my home network to the TP-Link WiFi 7 router, and the results have been nothing short of impressive. One of the standout features of this router is its remarkable reliability. In the fast-paced digital landscape of today, having a stable and consistent internet connection is paramount, especially in a household with four active kids.The reliability of the TP-Link WiFi 7 router has been a game-changer for us. Gone are the days of sudden dropouts during crucial online meetings or laggy video calls. The router’s advanced technology ensures a seamless and uninterrupted connection, even during peak usage hours. This has significantly improved the overall online experience for both work and leisure activities.Moreover, the coverage provided by the TP-Link WiFi 7 router is nothing short of expansive. Our home, previously plagued by dead zones and weak signals in certain corners, now enjoys a blanket of high-speed internet. The router’s signal strength easily reaches every nook and cranny, allowing all four of my kids to connect effortlessly from their respective devices.Speaking of my kids, their diverse online activities put the TP-Link WiFi 7 router to the test on a daily basis. From video streaming and online gaming to virtual learning and social media browsing, the router handles it all with finesse. My eldest, a gaming enthusiast, has experienced reduced latency and faster response times, resulting in a more enjoyable gaming experience. Simultaneously, my younger ones attending virtual classes have reported fewer connectivity issues and smoother interactions with their teachers and classmates.In conclusion, the TP-Link WiFi 7 router has proven to be a reliable and high-performing addition to our home network. Its robust connectivity, extensive coverage, and ability to cater to the diverse online needs of my four kids make it an excellent choice for families seeking a top-tier router. If you’re looking to upgrade your home network for a more seamless online experience, the TP-Link WiFi 7 router is definitely worth considering.

I was having some issues with buffering and video freezing errors on an app that I use in my ps4. I reached out to the Customer Service Dept for the app, and they offered a helpful solution. Unfortunately, it did not completely solve the issue. However, there was information that was added that was directed to my wifi router. So, I did some digging. Eventually I needed to chat with a Customer Service rep! A person named Kurt Sebastian connected with me. He asked questions in order to get a better handle on what I was trying to do and why. After I explained my situation with Kurt, he seemed quite knowledgeable in how to help correct the problem. Unfortunately, while I was trying to follow Kurt’s instructions (I needed to use another device during this point), the other device that I was using was plugged in for charging. Well, it still died on me, right in the middle of the process!!!!! I was scrambling to try other options and not loose communication nor waste Kurt’s time! Thankfully, Kyle was patient and gracious enough to maintain communication and because of that, everything is running as it should!!!! Thank you very much Kurt Sebastian for everything you did to help me improve my situation!

This runs a whole bunch of stuff – WiFi and LAN – typically about 15 devices. I’m not going to rate the Wifi because I’m not going to use it yet. 1) I have two EAP225’s; they’re VERY strategically located and they mesh with each other. Unfortunately they won’t mesh with this thing. 2) I don’t have anything else that will even do WiFi 7 yet.I got this mainly for the five 2.5 GbE ports – one WAN and 4 LAN’s! I’ve also got a Yeacomm (Speednet) NR610 (also a very nice, but expensive device), and my internet is blazingly fast! Just very snappy. Internet tasks are usually as fast as doing stuff locally on the computer. You can easily tell when it’s the website that’s slow. That Yeacomm has a 2.5 GbE port and I was drooling at the thought of getting that 2.5 GbE speed to the LAN. (I also have a gigabit switch, a PoE switch [for the EAP225’sand the Magic Jacks that only do 10 MbE], and two 2.5 GbE switches.) Really nice that all my stuff plugs into this!The WEB interface on this device is a thing of beauty! Everything is very logically laid out, most changes, you don’t have to reboot for, and if you know your network stuff, you’ll find it nice and easy to use.If you don’t know your network stuff, you’re still in luck! It took its time communicating with the Yeacomm (LTE CPE Modem) (and a bunch of other devices) on the first boot – maybe 3 minutes or 4 minutes – but it configured itself very well! I have two Magic Jack lines and those didn’t work right away. It took some hair-pulling-out time to straighten it out. But I’ve had one way audio problems with those before. This time, this router had the provisions to fix it (on one of them only.) That’s not this router’s fault; it’s just the way it is. You need to forward a range of ports on two different devices and you can’t. It took a very long time to get fixed. It was like a combination lock. Turns out the final step was some settings in the Yeacomm. The Magic Jacks now talk directly to the cell phone tower. One of them works perfectly and the other one only has one way audio when calling [mostly] cell phones. If I had another 2.5 GbE port on the Yeacomm, I could do it, I think, but as long as I can get calls on both lines and call out on one of them, I’m happy.Everything else worked like a champ with settings that this router came up with all on its own! The only thing I changed (not counting the Magic Jack settings) is making a bunch of MAC | IP reservations.When you set it up, you get a light show for awhile. Then the lights can be turned on or turned off with a WEBUI switch. You can also set up a night time mode and have them on in the daytime and off at night, specifying the times. You can plug a USB hdd into the USB port and use it as a very fast, very big network share. It’s almost like having an NAS. It’s been totally stable and reliable so far.It’s a lot of money. I had to talk myself into it. I shopped for about a week. That should tell you something. Now that I’ve gotten to use it, I consider it well worth the money! I give their tech support 5 stars, not because of this thing, but because I’ve used their tech support in the past and I already KNOW it’s exceptionally good! I have a lot of other TP-Link stuff. Advanced, hi-end stuff.Half of the 12 connected devices shown in the pic.

TLDR:I bought this router about a month ago when my older one started to stutter. After some initial issues with firmware and a round or 2 with TPLink tech support I got everything ironed out and now I am very pleased with the performance. For more details, please read on.I’m a Network Engineer who works from home. Internet access is critical to my ability to do my job. So, when my older Netgear wireless router started to show signs of failure (random WIFI network loss of signal and reboots) that I could not fix with firmware updates, I started searching for a new router.The BE550 is a slightly less expensive version of TPLink’s top end router. It lacks the extra LEDs on the front that allow for it to display the weather and a few other cute features, and it only has 4 LAN and 1 WAN(Internet) connections, all of which are 2.5G. there are no 10G ports on this router. Since I don’t need to move that much data, it wasn’t a deal breaker for me.Install was pretty easy, but I was also taking the opportunity to upgrade my Cable modem to a newer model and to install a 2.5G NIC in my home PC. After initial bootup and configuration of my home and guest networks, I ran speed tests that showed significant improvement in throughput. I have Gigabit service and improved my wired speeds from 690Mbps average to 1.1Gbps average on my home computer. The 2.5G ports are really doing there jobs and keeping the data moving without a bottleneck.Unfortunately, after about 24 hours, the new router became unstable. The wireless signal would cut out, and even wired connections would lose internet access intermittently. As I tested components I ruled out the Cable modem and the new NIC and started to focus on the router. Constant ping tests to google would randomly time out for 20-30 seconds and then return. At the same time the LAN side access into the router would be lost, which shouldn’t happen if the loss of signal is on the Internet side.I opened a ticket with TPLink and was surprised by how quickly they responded. After some initial testing with a tech on the phone, the ticket was kicked to the next level of support and all subsequent support was via email. The techs asked for log files and information about my troubleshooting and the analyzed that for about a day. They then sent me a firmware update (which wasn’t available via the firmware update process in the router) and asked me to apply it. Once that was done, the router stabilized and hasn’t shown any issues for about 48 hours.Like:Design – more like a book than something from a Star Trek movie.WIFI Coverage: Even with internal antennas, I have very good coverage of my 2000 sq. ft. house and my backyard.WIFI Speed: Phones and tablets are easily pulling 8-900Mbps from anywhere in the house.WIRED Speeds: My desktop (with 2.5G NIC) is able to pull 1.2Gbps easilyDon’t Like:GUI: Maybe I’m just picky, but I think the GUI needs help. It isn’t as intuitive as the Netgear router I replacedPrice: This is an expensive piece of kit at $300+ Overkill for a lot of people, but there are limited 2.5G capable wifi routers on the market

As A Spectrum Internet CustomerI had a Spectrum Advanced WiFi router that does 2G and 5G on the same WiFi network. There is not a way to split the networks in two. If you have a cell phone that is compatible with device steering and you use to connect your 2G devices to, you can call or chat with their Internet Repair support team to set up a feature on your cell phone that may allow the 2G devices to connect but it can be a hit or a miss and it’s too much of a hassle to keep calling/chatting to set this up with as the feature is enabled for only sixty minutes. If the 2G device is connected before the hour is over, it will remain connected but if it’s not, you’ll need to reach back out to try again and you’ll also need to reach back out for other new 2G devices only that don’t automatically connect to the 2G network.This is a major flaw for an “Advanced” WiFi router. Customers paying a monthly $5 fee to lease their routers should be able to either split the networks in two or leave them as a single network for band steering. Outside of this, the Spectrum routers are fine. However, it’s just better to get your own router.It would be great if they offered more advanced routers with more features such as VPN’s, hiding network SSID, splitting the 2G and 5G networks, guest network and more. I’d pay $5 more a month on top of the already $5 charge for this. This way customers can select which router they need for their home and still get customer support for it.As A New Customer For Echo Dot’sThis is the reason why I purchased my own router. I purchased four Echo Dot’s, 5th generation, ’22 release. All of them connected to the Spectrum WiFi router without issue and individually they operated great. However, the Echo Dot’s have a “multi-room audio” feature where you can play music all throughout your home. This was my entire reason for getting these in the first place. This feature was a hit or miss. Sometimes it would work but most of the time only one or two would work and trying to get them all re-paired so I could say, “Alexa, play Discover Weekly from Spotify everywhere,” was a huge inconvenience and took too much time.After going online and reviewing forums such as Quora and Reddit, I could see what the issue was. The Spectrum WiFi router would switch them between 2G and 5G based off of interference and signal strength throughout the day and if even just one Echo Dot was on a different network than the others, it would throw off the multi-room audio so that it wouldn’t work. So the hunt for a dual band router began.TP-Link AX1800 WiFi 6 Router (Archer AX21) ReviewThe TP-Link AX1800 Router has been amazing so far. It arrived on the same day that I ordered (Thank you Amazon and of course, most of all, the delivery drivers). When it first came in, the first thing I noticed was how ridiculously light it was which kind of made me nervous about the purchase. The router itself came very nicely packaged, nothing was damaged.I followed the instructions to the letter but the router was not showing any lights on there after plugging it in once the Internet modem came back online. I re-read the steps again and re-checked the power connections and tried unplugging from both ends but not luck. I honestly thought I got a dud. I looked on the back of the router and saw a button and pressed it in; all the lights began to show and I could begin the setup process.I use an iPhone and when I pulled up the TP-Link App to set up the router I couldn’t help but notice its low star rating so I opted not to download the app and instead login using the IP address (the instructions provide you with this information and how-to as well). This is my first time ever logging into a WiFi router without the use of a mobile app and I have to say, it is significantly better and heavily preferred. I was able to turn off TP-Link Smart Connect so that I could have two separate SSID’s for the 2G and 5G network. I could also see there was a whole new host of features that I did not have prior such as hiding your WiFi networks from neighbors and having a guest network.I also did a speed test and they all came back higher than normal and my computer noticeably moves faster when browsing the Internet and streaming video despite being roughly around the same speeds (before it was around 310mbps download/9mbps upload; now it is at around 360mbps/13mbps upload). Maybe the 50mbps DL and 4mbps UL makes a huge difference. I’m not entirely sure. I believe the difference really comes from the router provider a more stable/stronger connection than the Spectrum router. The signals itself are just healthier now.I also like that the TP-Link router has antennas, four of them to be exact, that you can see. The Spectrum routers don’t have these and if they do, they’re within the router itself. I believe routers with antennas that you can visibly see operate better and send stronger signals.Did This Resolve My Issue With The Echo Dot’s?It absolutely did. I re-connected all four Echo Dot’s to the 2G network, which was kind of a pain as well to do (but well worth the time and effort; it would’ve been significantly easier to do if I originally connected them to a dual band router in the first place) and ever since then I have had no issues with multi-room audio. Anytime I want to play music from all four Echo Dot’s at the same time, they all play without issue. Which is great because I plan on purchasing more for a more surround system environment.Final NotesIf you need a dual band WiFi router that is able to split the networks in two so that you can sign into them separately, this is it. And honestly, if you have a Spectrum router, this is a major upgrade for a fraction of the cost. Just make sure you keep it clean of dust, and keep it in a well-ventilated and cool area of the home and this will easily last you 2+ years. It saves you money and it works better. It’s honestly a no-brainer.There is also a common misconception with spotty/slow Internet speeds. The majority of signal issues do not come from cable lines (confirm with your ISP provider first though that the signal levels look healthy coming into and from your Internet modem) but come from the equipment itself (modem and/or router) or from the devices you are using (assuming it is only occurring on one or two devices). Which is why upgrading your WiFi router and/or Internet modem can resolve the issues.I honestly don’t have any issues with the Spectrum Internet modems. I think they’re fine. They all come pre-built, meaning, you can’t change any settings on them. Not a deal breaker for me. However, honestly, if I didn’t have a Landline service with them, I would’ve purchased my own modem as well and long-term wise I will definitely consider it. The Spectrum Internet equipment are fine for the majority of homes. However, there is no one size fits all and if you’re having issues with your equipment whether due to the lack of features available or signal issues (and confirmed with their Internet Repair team that there are no signal issues coming from the lines), this TP-Link router is an exceptional purchase.

Had to get this because my old router just can’t keep up anymore, both of these speed tests were taken from the same room on the same device and the new router increased my download speeds tenfold! But you still need to know what you need when ordering, as I didn’t realize we had our phone line hooked up to the old router, but luckily I was able to connect this new router directly to the old one’s LAN port and after a quick reset with the button on the back (you will need a paperclip or earring) I was able to get this router set up with ease! You will want a computer connected directly to the router to make setup easier, then just follow the link that is on the bottom of the router. It can detect what kind of IP your ISP gave you if you aren’t certain like me, which was a huge help! I’m getting much closer to the speeds my ISP claims I should get and haven’t had any serious issues yet! I also recommend that you set up both the 5GHZ and 2.4 GHZ bands, which is as simple as checking a box in the setup and making a name and password for each band. In around 20 minutes or less, you’re done! I hope this helps!

Side note: I actually got this unit about a year and half ago and ultimately had to return it because it kept loosing connection every 30 mins. I tried everything to troubleshoot it: Google, forum, tech support, etc and nothing worked. Ended up returning it for a refund.Skip to a few months ago and I decided to give it another try since it was time to retire my old Archer. Also, this model kept popping up as the best midrange wifi 6 router for its price. Glad I did because I haven’t had any issue since setting it up. It was extremely easy too, I even used my old ssid and pw. All my devices connected without problem and best of all, no more device disconnects. I only have a few devices that are wifi 6 while the rest are wifi 4 and it handles everything without issues. Signal is also really good. I have it placed in the corner on the 2nd floor of my home and I get full signal bars everywhere including the garage. I live in a 2000 sqft 3 story townhouse. As mentioned, been working fine since I got it. Moral of the review, if you get a defective unit the first time, try again. Sometimes we get unlucky with a defective unit, but that shouldn’t be an indicator that all units are bad, unless it’s your 3rd one.

For context:Internet Service: 1GB/sInternet Provider: FrontierHome SqFt: 3,300So Frontier provided me an Eero router and extender initially. My speed download was averaging at 20mbps download and upload. My office could not get service to save its life. It came with a router and extender.Well I installed just this bad boy. Now I’m at 150 mbps average download AND upload. (I know there’s a drop off in wifi because it’s wireless)I LOVE this thing. Easy to setup in the app as well. PLEASE BUY THIS ROUTER

And after 1.5 hours, could NOT get this to sync. Returned for quick refund…wanted updated wifi 6 speed to watch 4k programs without freezing up or buffering. I did have cable co out to check if all was working…ok.Always had around 80mbsp speed and he got up to 386 with new router, WAY past the 300 average. This is capable up to 1 gig; in case I want to upgrade. I just wanted something to view uninterrupted streaming services and GLAD I purchased because it made a HUGE difference. Never had a problem of range (1600 s.f.) with old router but this has greater/stronger connection as well.

So it been about 5 years since I bought a router. My old Netgear R6020 worked as expected , No issues other than the fact that I was mislead that it would be faster than 100mb. Recently , I added a lot of devices to my home network. Running speed tests I could get as high as 90mb…Research told me that this Netgear router was in fact a 100mb router… I am paying for a 150mb internet speed…I searched many routers and decided on this one. Setup was fairly easy …And making a TPLINK account lets me control this router from anywhere. That’s a pretty awesome feature to have . So , I used the same Network logins as my previous router , Enabled the smart device , and let the router do its job. Some people had issues with the smart network feature , but I updated the firmware , let it boot up , and all 13 of my devices were instantly connected. They are a mix of wired , 2.4 , and 5g devices. All 5g devices connected properly. Now , the test I was waiting for . The speed test…All speed tests now result in over 160mb …I am a happy camper . The phone. Computer , video cams , are all faster and the signal strength is great. I am so glad I chose this router , and I think you will be happy with it also !UPDATE : After playing with all the settings for a couple weeks , I chose to disable ” smart connect ” and run the same name and password SSIDs for the 2.4 and 5g . Enabling Smart with multiple devices let’s the router control the network…With it off it lets the device control it . Some of my dual frequency devices were dropping to the 2.4 network ( which my security cameras are on ) with smart connect enabled….A flick of the switch and now that the devices choose the network , 5g devices tend to stay on the 5g network all the time. Performance and range have been perfect so far , any other issues and I will update !And as Promised , here’s my update : After 1 year of using this router with 13 devices connected 24/7 ,I can say this router is a beast ! No issues , great string signal everywhere in my house and yard ….But it , and you won’t be disappointed..The APP is fun to play with when you are not home , and is very easy to use. I have stuck with the smartsetting off , and let my device pick the network…My 5g devices stay on 5g then , and my 2.4 network has less traffic this way ….Update : It’s been a year since I bought this router and not once has it failed me …It’s a workhouse, and I have 15 devices using it …You will not be unhappy with this inexpensive long range dual band router !

th warranty support – rating and review update. Original: It was a good router while it lasted, but I expected it to last a couple years, at least, not less than one! When I went to register it for warranty support the TP-Link website said the serial number was not from the US. I had to provide further proof. So we’ll see if they make good on the warranty. Meanwhile I need wi-fi NOW, so I’m off to buy a new router. If TP-Link covers this dead one and I end up with two routers, then I’ll have a backup for when the next one dies, which is not a bad thing.Update: I was able to register my router in a couple of days and contacted warranty support. They replied quickly via email. (I had the option of email or phone.) There was a list of steps to try to get wifi working again. I was going carefully through the list and suddenly noticed the wifi light on the router was green. My router is not dead after all and I’m using it now.I have the usual number of devices: TV (streaming), phone, laptop which could all be in use at once. I generally have no issues. I reboot once in a while, but I noticed on the app you can schedule a regular reboot which might be a good idea. It’s a good, reasonably priced router for anyone who doesn’t need anything fancy.

I would consider myself a novice when it comes to routers and networking. I can do simple tasks (network set up) adding removing devices..etc changing passwords etc. For the past few months, i have been on the fence about replacing my ISP provided router, so i took the plunge and orderd this model (archer ax21).my old netgear router (supplied by my ISP (charter spectrum) died back in november and I called customer service and they sent me a new “advanced wifi” router. that router was complete garbage, ISP’s don’t even let customers go in and modify their own home wi-fi networks. if you type the ip address for the router, it directs you to a page that says “login using the spectrum app”. well, their app only allows you to change the SSID name and password..NOTHING ELSE. very frustrating. ISP provided routers now combine the 2.5ghz and 5ghz bands, and many of my devices are older and ONLY use the 2.5 ghz band. so, natrually there were conflicts and frequent disconnects. I also own a accurite iris 5 and 1 weather station. in all my years of using a pc and wireless networks.. I have never seen or had a device that is so tempermental. I needed to be able to isolate the 2.5ghz and 5ghz bands so that i could assign specific devices to each band. the older things go on the 2.5ghz, and newer things like ipad, smart tv, xbox one..go on the 5ghz band.setting this up was very straight forward. simply power down your ISP modem, and reboot. wait for everything to reboot and ensure you have internet connectivity through the modem. then plug ethernet cable from back of modem into the WAN port on the Archer X21 router. then power up the router and wait for all the lights to turn green. takes about 1-3 minutes tops.you can set up either via APP (which is what i did), or you can set up using pc with ethernet cable.I have a chromebook, so it has no eithernet jack. i actually ordered one on amazon, it’s a usb to ethernet adapter. works like champ. but for most people you should be able to set up just using the app.. if you want to do more advanced things (dchp customizations, etc) i would set it up on the webpage through the ethernet connection.simply follow the instructions from the app, enter your new network name and new password and you will be good to go.the app shows each device connected on each network as well as real time uploads/downloads so you can see if there is a issue with a particular device. if you are having issues with devices disconnecting/reconnecting/slow speeds etc. i would suggest at the start that you DISABLE the 5ghz band. after you get everything connected and confirm that the devices are working, then go ahead and re-enable the 5ghz band. for some reason, (not sure why) on inital setup there can be conflicts.there are tons of options for this router, far to many to get into much detail for this review. go ahead and download the manual prior to purchase, so you can read up on what this router can/can’t do before you purchase.you can actually update the firmware over the air by hitting the update button, or you can speciify a certain time of day for the updates to be installed. a good rule of thumb would be set it to sometime after midnight that way, you will be asleep more than likely when the updates happen. out of the box, mine needed a firmware update. took less than 5 minutes.i’ve had/currently have other tp-link products (smart bulbs/cameras) and they all work as expected.the app is very intuitive and straight forward. i didn’t have to have any special settings from my ISP, i just plugged in the router, went through the setup, and everything connnected flawslessly on the FIRST attempt. no errors/timeouts etc that i was getting with my ISP supplied router.the router is sleek and has 4 antennas. my range is about the same as with my previous isp supplied router. currently have a linksys re6300 extender out here in the living room to boost the 5ghz band. my house isn’t that big but is very old. (its a single wide from early 70’s with A-Frame roof). so i think my signal loss has alot to do with the aluminum siding on my house. your range/results will obviously vary.I currently have 16 devices on my network and all are staying connected flawlessly and seem faster than with the ISP supplied router.there is also a option for guest network. I’m using that for guests and my accurite weather station.hoping this will help me troubleshoot the accurite when the inevitable disconnects start.also wanted to mention that the accurite iris 5-1 weather stations are full of problems. if your considering one, go with another brand. it’s not worth the headache.the only reason i took a star off was becase the antennas on the back of the router were wrapped in plastic that was hard to take off. other than that, i think this router is perfect. it’s affordable, has tons of options and doesn’t have performance issues that ISP supplied routers do. pick one up today, i’m sure glad I did.***update 9/24/24*** 1 year and 8 months later, router still performs PERFECTLY! no issues at all, adding static ip addresses to devices is very easy, and great connectivty. never had one single issue with this router. i have multiple devices across both bands (2.5ghz and 5ghz) and i haven’t had any problems, even my nightmare accurite weather station works perfectly. the key to that device, was connecting it to the 2.5ghz guest network by itself. may want to keep this in mind for devices that are giving you trouble, i have found by isolating troublesome devices, they tend to stay connected when connected by themselves. this router offers many options, lots of them i don’t even use. even after multiple power/interent outages, once power/service returns, everything reconnects in less than a minute. every tp link product ive ever owned has performed perfectly. great job tp-link!

ter to cover a house. Now I have to say up front I was close to regretting getting the Archer AX21. I had it up and running in about 5-10 minutes but, for the first 5 days the wifi devices using it were losing their internet connection multiple times a day and the only way to resolve it was to rebooting the modem. I started to think maybe some of the bad reviews here were true.I started checking settings, reaching out to TP-LINK (great response form them) and to Motorola, for my cable modem/router combo settings. Turns out I did not have the Motorola device correctly set for WLAN and Bridge mode (note, the AX21 setup even sees another router and suggest placing the other into Bridge mode, it’s just that the Motorola modem required another set to configure the WLAN). Once that was set the router has been up and running and devices working with it for a week now with no issues. TP-LINK also had me change some of AX21 internet settings, which I first thought may be part of the issue, but since correctly setting the modem I have changed the AX21 settings back and it still works fine.The wifi coverage on the AX21 is great. My 100yr old house has plaster walls and large central brick chimney. The cable modem/router is set up in a back room/office but it had weak coverage to the opposite end of the house even with the TP-Link extender I already had. I ran cabling to place the AX21 in the living room, near the center of the house. Once set up, the coverage is great. I like that I was able to change the extender to OneMesh mode and move to another corner of the house to improve outside coverage for some external security cameras and have one wifi ssid throughout; the dual mode also split out the 2.4ghz (used by the security system) and the 5ghz used by our tablets and phones. The only wifi version 6 devices we have are our phones and yet on a speed test on all of our wifi devices were able to get the full speed of our cable internet service. The AX21 and one the one indoor OneMesh extender even covers our entire very large backyard.Note: If I had wanted to keep using the wifi capabilities of my existing modem/router device, I could left the modem in its default settings and set up the AX21 in access point mode, but I would lose the OneMesh capabilities I wanted for a single network with at least one extender, and my older modem combo only had 2.4ghz, so best for me to use the AX21 as a router and it’s full capabilities.I also like the web admin console and the tether app for the degree of control they provide, from features like checking clients connected and reserving IP addresses to little things like being able to schedule device lights off at night.

sy setup with app. I just received the TP link AX1800 a few days ago, so can’t speak to long-term performance. I was replacing a 5-year-old NetGear WiFi 5 router that worked great until it started recently and randomly dropping signal to my work and personal computers and was likely at the end of its useful life.Out of the box setup and operation of the AX1800 were very easy with the TP Link app I downloaded to my phone. I followed the directions of powering off my modem, connecting the modem and router via provided ethernet cord, then powering on the modem and router.Once both devices were fully powered, the app guides you through an easy to follow set of steps to get everything connected. All told, it took maybe 15 minutes from opening the box to having a signal to all my devices (hardest part was getting the damn plastic wrap off the antennas!). I have noticeably faster performance with all my devices now with the improved WiFi 6 technology vs. the older WiFi 5.I have a small condo, less than 1,000 sq. ft., with about 8 devices using WiFi, so I’m not in need of the biggest and baddest router that maybe a gamer or multi-person, larger household might want. This one has, so far, worked very well for my needs, and at a very reasonable price of about $70 on sale.One suggestion: This router tends to run hot, especially on the bottom, even though the manufacturer has upgraded the design from the older model to dissipate heat better. I attached some small squares of foam packing to the four bottom corners to raise it off the shelf an inch or so and that seems to help.

orks Great. We have had the TP-Link AX1800 (Archer AX21) Router since 11 July 2022. This is being written on 27 Oct 2022.Setup was straight forward and it has worked flawlessly since then.It replaced an expensive 3 unit fancy mesh wifi system that was always failing and did not have great coverage and totally failed after a few months. Prior to that we had an Apple WiFi Extreme for over a decade. Apple has abandoned the WiFi market and their WiFi customers.Our apartment is two floors plus the cellar in a 125 year old masonry building. The ceiling/floor between the two floors is a foot thick. The ceiling is lath plaster. The floor above is a thick wooden sub-floor with parquet overlaid on it. It is supported by large wooden floor beams. Each floor and the cellar are each about 800 square feet.The TP-Link AX1800 is located on a shelf about a foot below the ceiling against one of the masonry walls.Both floors get excellent WiFi coverage. The cellar, which has a metal ceiling, gets OK WiFi coverage.In addition their is an iMac on each floor connected via Ethernet. There is also a Roku on the first floor connected via Ethernet.On WiFi we have three iPhones, two iPad Minis and three iPad Pros. They all work great on both floors and the signal never drops as we each go about the apartment.We highly recommend the TP-Link AX1800.